Solar Shade Blade Attachment Systems
System 1
| Dimensions | LS1 - 55 | LS1 - 65A | LS1 - 65B |
|---|---|---|---|
| Note: Table to be used as a guide only. Allowable dimensions depend upon the specific requirements of the project. | |||
| A mm (max) | 2500 | 3300 | 3300 |
| B mm | 300 - 500 | 350 - 550 | 420 - 600 |
| C mm | 60 | 60 | 60 |
| Angle of rotation ° | 0 - 100 | 0 - 100 | 0 - 100 |
| Torsion tube Ø mm | 55 | 65 | 65 |
Intended for wider spans, carrier system 1 incorporates a central aluminum torsion tube along the length of the louver, and is ideal for continuous facades, as well as for roofs.
For glass, cross sectional louver widths from 11.75" and up to 23.5" are available.
This carrier system is also suited for use with metal, fabric, wood, terracotta clay and translucent acrylic louvers.
System 2
| Dimensions | LS2 - 30 | LS2 - 301 |
|---|---|---|
| Note: Table to be used as a guide only. Allowable dimensions depend upon the specific requirements of the project. | ||
| A mm (max) | 2000 | 2000 |
| B mm | 500 | 550 |
| C mm | 60 | 60 |
| D mm | 10 | 10 |
| E mm | 1700 | 1700 |
| Angle of rotation ° | 0 - 100 | 0 - 100 |
Primarily intended for smaller spans or where frequent anchor points are available, carrier system 2 provides minimum obstruction to the glass area, thereby maximizing daylight and enhancing the view to the outside.
For glass, carrier system 2 is available with cross sectional louver widths of up to a maximum of 19.5".
This carrier system is also suited for use with metal, fabric, wood, terracotta clay and translucent acrylic louvers.
System 3
| Dimensions | LS3 |
|---|---|
| Note: Table to be used as a guide only. Allowable dimensions depend upon the specific requirements of the project. | |
| A mm (max) | 4000 |
| B mm | 600 |
| C mm | 60 |
| D mm | 5 |
| Angle of rotation ° | 0 - 100 |
Like System 1, carrier system 3 is intended for wider spans and incorporates a discreet central aluminum torsion tube along the length of the louver. It is ideal for continuous facades as well as for roofs.
For glass, louver spans of up to 13 feet long can be achieved without any additional supporting structure.
Glass louvers can have a cross sectional width of up to 23.5".
This carrier system is also suited for use with metal, fabric, wood, terracotta clay and translucent acrylic louvers.
System 4
| Dimensions | LS4 |
|---|---|
| Note: Table to be used as a guide only. Allowable dimensions depend upon the specific requirements of the project. | |
| A mm (max) | 1800 |
| B mm | 600 |
| C mm | 65 |
| D mm | 10 |
| Angle of rotation ° | 0 - 90 |
Carrier systems 1, 2 ,3 and 5 are pivoted systems which require the supports to be connected to each side of the louver. System 4 provides a back hung design solution with hidden control mechanisms integrated within the main vertical supports. This allows for seamless continuous louvers with unobtrusive supports when viewed from the outside, due to the louvers being installed in front of the supports.
For glass, carrier system 4 is suitable for smaller spans of up to 6 foot in length. It can utilise cross sectional louver widths of up to 23.5", incorporating photovoltaic cells if required.
This carrier system is also suited for use with metal, fabric, wood, terracotta clay and translucent acrylic louvers.
System 5
| Dimensions | LS5 |
|---|---|
| Note: Table to be used as a guide only. Allowable dimensions depend upon the specific requirements of the project. | |
| A mm (max) | 1800 |
| B mm | 600 |
| C mm | 50/60 |
| D mm | 10 |
| Angle of rotation ° | 0 - 100 |
Carrier system 5 is a fully centred pivoted system which provides maximum transparency. Louvers are supported at each end by a bonded and extruded end cap.
For glass, louver spans of up to 6 foot long can be achieved without any additional support work. This system can utilize cross sectional louver widths of up to 23.5".
System 5 is ideal for either horizontal or vertical applications.
This carrier system is also suited for use with metal, fabric, wood, terracotta clay and translucent acrylic louvers.
